Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5896 visitantes y 
2 usuarios online.
Productos
Información
Destacado
Inicio >> PHILIPS >> LTC5108/50 Manual de Usuario
 
 0 artículo(s) en Su carrito 

PHILIPS LTC5108/50
Manual de Usuario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del PHILIPS LTC5108/50 Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como archivo PDF después de que lo compre.

El Manual del Propietario (a veces llamado Manual del Usuario o Guía del Usuario) contiene información sobre cómo utilizar su dispositivo. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
4.3

Video Inputs and Looping Outputs

4.6

Programming System Setup

For each of the 4 or 8 channels there are two BNC connectors on the rear panel. One of these connectors is to be used as a video input while the other connector may be used as a looping output. It does not matter which connector is used as the input and which is used as the looping output. Each pair of BNCs provide an automatic termination function that applies a 75 ohm load to the incoming video signal when the cable is connected to either jack. When �loop-through� operation is desired, the second cable connection automatically unterminates the input providing the required high impedance for �loop-through� operation. The jacks act as automatic switches. The looping video outputs are provided to supply video to other video equipment. When looping, the last piece of equipment on the video line should be terminated

Configuration options are provided through on-screen menus. These menus are accessed by using the DWELL key. With video present on the monitor, a momentary press and release of the DWELL key will gain easy access to the Dwell Time Menu (see Screen 1).

4.4

Monitor Output

The monitor outputs are designed for a 75 ohm load. Therefore if you loop the monitor output cable through multiple monitors or their accessories, be sure their terminations are set to Hi-Z. Only the last unit on the line should have its termination set to 75 ohm. LTC 5104 Series: A single monitor output permits switched camera video through this connection. LTC 5108 Series: These switchers may be used with one or two monitors depending on system requirements. See Operating Mode section and Typical Installation illustration.

Screen 1 The remaining configuration menus (8 for LTC 5104 Series and 9 for the LTC 5108 Series) are also accessed with the DWELL key. With video present on the monitor, press and hold the DWELL key for 1 second; the monitor will display Screen 2.

4.5

Alarm Inputs and Output (Accessory Output)

A cable with a connector is supplied to connect alarm closures or other accessories to the switcher. The alarm inputs can be triggered by either a contact closure selectable (normally open or close) (e.g., switch or relay) to ground or by a logic ground (e.g., motion detector output). The alarm output creates a short between the two output pins when an alarm occurs and open-circuits the pins when no alarms are active (triggered). The alarm output has a maximum carrying current of 1 A and a maximum switching voltage of 40 V AC/DC. The alarm output can be used to signal a VCR, lamp, or relay. CAUTION: Do not apply external voltages to the alarm inputs. Use only isolated closures. Precautions should be taken particularly on long runs, to prevent pickup of spurious signals from associated wiring which may give false inputs or damage the switcher.

Screen 2 To advance through these 7 or 8 menus, press the RUN/next key. When the last menu is displayed, the RUN/next key will automatically exit the configuration mode. The configuration mode will also exit automatically if there is no activity for 60 seconds. Use the DWELL key again to exit the configuration mode immediately. Any changes made during configuration are acknowledged regardless of how the configuration mode is exited.

6

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.164 - Number of Queries: 130 - Query Time: 0.043